Heating Repairs
in San Antonio, TX. Same day 24/7. Call toll-free: 210 538-9875
Welcome
to San Antonio, TX Appliance Repair
we are locally established company specializing on
San Antonio, TX Heating repair. San Antonio, TX Appliance Repair has
more to offer than most local contractors.
- We provide same day San Antonio, TX County Heating Service
24/7
- Service call, free with the Heating repair
- $15.00 off coupon
online
- San Antonio Certified Technicians on All Major
Heating Brands/ Models
- We serve all San Antonio, TX County
- Low price
Guarantee
- Satisfaction Guaranteed
or Your Money Back!
We service entire San Antonio, TX and surrounding areas including
:
San Antonio
Hondo
New Braunfels
Canyon Lake
Live Oak Helotes
Castroville
Marion
Floresville
Spring Branch
|
Cibolo
Fair Oaks Ranch
Adkins
Helotes
La Vernia
Pipe Creek
Boerne
Bandera
Devine
|
Schertz
Live Oak
Bulverde
Converse
Seguin
Pearsall
Jourdanton
Pleasanton
Fischer
|
Veiw the our entire San Antonio, TX service area
You can always check our easy to repair Heating tips
or let us take care of all your oven needs.
At San Antonio, TX Appliance Repair we want to help you managing
your busy life and schedule your San Antonio, TX Heating Repair
appointment as conveniently as possible. As always,
you can call us at:
210 538-9875
You may now schedule your appointment online. Please
send us an Email at appointment@sanantonioappliancerepairservice.com
and submit your name, phone number, address and brief
description of the problem. We will confirm your appointment
in the next 60 minutes
Emergency
repairs/ No heat
On electric heater, if lop thermostat shuts off power,
push reset button once. If cutoff recurs, upper or
lower thermostat or heating element is defective.
Have it replaced. On gas heater, if pilot light ,,
off, relight it following detailed instructions printed
on metal plate on heater. If you are unsure of how
to proceed, call the gas company. If pilot light still
goes out, clean openings vith a thin copper wire,
arid brush out air inlets at base of heater. If problem
persists, replace thermocouple
Prolonging heater life.
Water heater tanks corrode and can rust out completely,
causing a flood, in less than 10 years. However, every
heater has an anode, a magnesium tube that attracts
impurities and corrodes itself instead of the tank.
Have anode replaced ,every 15 years 00 years WAk a
10-year guarantee). Most anodes are rigid, but flexible
ones are available for heaters W16"t 6 in. of
space overhead.
IMPROVENEENTS THIAT LOWER HOT WNIFER COSTS
Ading more than you need for hot water is the same
as pouring energy dollars down the drain. Here and
on the following pages, you'll find hands-on instructions
that show you how to fix leaky faucets, install watenconserving
devices, and investigate more economical ways of heating
water plus two energy-efficient suggestions for getting
hot water where you need it. Over time, you can expect
energy saAngs to repay your investment in these measures,
sometimes generously.
ADDING A MONEY-SAVING FAUCET AERATOR
A faucet aerator works by mixing air into the water
stream. The result is a high-pressure flow that uses
less water than a. solid stream. An added beriefit
is that an aerated stream does not splash. In normal
household use, aer& tors installed on all your
kitchen and bathroom faucets can save the BTUs needed
to heat several hundred gallons of hot water a year.
For maximum effect, look for a kitchen aerator rated
for a flow of 2.5 gallons per minute (GPM) or less,
and for a bathroom aerator rated as low as I GPM.
Replacement aerators are generally made to fit faucets
with spouts that are threaded either on the inside,
or the outside. Some swivel so that you can direct
the stream where you wish; others have a built-in
control that allows you to interrupt the flow- without
also affecting water temperature. An avaporator comes
with a rubber or plastic washer. To install the aerator
on a spout with inside threads, place the washer on
the aerator, discard the washer when fitting the aerator
to a spout with outside threads. Screw the aerator
on hand tight. (If the faucet and aerator threads
don't match, purchase an adapter from your local home
center or plumbing supply dealer.)
REPLACING A WASTEFUL SHOWER HEAD
Installing a low-flow shower head rated at no more
than 2.5 GPM can be one of the most effective ways
to save money spent to heat water. Start by taping
the jaws of a pipe wrench to avoid marring shiny.
finishes. Use the ,wrench to keep the showier arm
from turning while you tuiscrew, the old shower head
using an adjustable wrench or a second taped pipe
«Tencb.The new shower head screws directly onto
the shower arm Lmless it has a ball joint at the end.
In that case, you'll need a standard half-inch threaded
shower head adapter. To install the adapter, wrap
one end with pipe-thread tape and screw it tightly
into the ball joint. Apply pipe-thread tape to the
shower arm or the other end of the adapter, then screw
on the new shower head hand tight using any washers
supplied by the manufacturer. If water leaks from
the joint, tighten the new shower head with the tools
you used to loosen the old one.
Call us at 210 538-9875 for
Appliance repair in San Antonio, TX. Free service call within
repair.
|
